Model: 05-0009
Stock: 53
Crank Main Bearing (Special Roller type) - 3 used per engine. - Located center (2) and Left hand side of crankshaft (1).
Genuine Yamaha Bearings made by Koyo
Fits: All 1970-84 650's ..
$167.00
Ex Tax:$151.82
Model: 05-0008
Stock: 37
Crank Main Bearing - Drive end - RH (Ball Type) - B6306C3 - Special. 1 used per engine. -
Genuine Yamaha Bearings made by Koyo
Fits: 1970-84 650's
..
$110.00
Ex Tax:$100.00
Model: 05-0012
Stock: 15
Crank Pin - Fits: All XS/TX 650's (1970-84) right or left side, 256 or 447 type engines...
$25.00
Ex Tax:$22.73
Out Of Stock
Model: 15-0681
Breather Filter with rubber end...
$15.00
Ex Tax:$13.64
Out Of Stock
Model: 15-0682
Breather Filter with Chrome Steel Ends...
$22.50
Ex Tax:$20.45
Model: 49-0821
Stock: 3
Stylish new front wheel hub is crafted from solid billet aluminum to the same dimensions as the stock XS650 hubs from 1972 and later XS650's.
36-hole
Silver Anodized
Designed to replace the cast mag wheels on the 1978 and later XS60's, these hubs can be adapted to any custom bike.
Ac..
$235.00
Ex Tax:$213.64
Model: 49-0820
Stock: 4
Stylish new hub is crafted out of billet aluminum to the same dimensions as the stock XS650 wheel hubs.from disk brake models (78-83).
36-hole
Anodized SIlver
Accepts identical bearings (6304), bearing spacer, axle (20mm diameter), brake rotor and stock sprocket
Designed to convert the..
$395.00
Ex Tax:$359.09
Out Of Stock
Model: 66-7702
Polished Chrome finish Custom/Sport Front Fender. Fits: All 1977-84 650's. Mounts to lower fork legs same as original fender. 12mm. mounting holes @ 2 3/8" (60mm.) center to center. Fender is heavy guage steel construction, approx 5 3/8" wide and fully chromed. This fender is a tight fit and doubles..
$115.00
Ex Tax:$104.55
Model: 49-0700
Stock: 109
Chrome Cylinder Head Crown Nut for top end hardware Kits # 49-0651/49-0653
10mm. x M1.25 x 21mm. High x 17mm. Hex..
$7.50
Ex Tax:$6.82
Hot
Model: 01-0651
Stock: 60
Brass Cylinder Head Washers - Can replace all cylinder head sealing washers or all Head Nut Washers used on any 650. 22mm. OD x 10.5mm. ID x 4mm. Thick..
$3.80
Ex Tax:$3.45
Model: 01-0650
Stock: 66
Cylinder Head Sealing Washers - OEM Ref.# 90210-10004 (4 used per engine) Steel Head washers with internal seal. Used under 4 outer cylinder head crown nuts on all 650's. Note: Not included in gasket sets. OEM Made in Japan...
$6.50
Ex Tax:$5.91
Model: 05-0757
Stock: 2
Cylinder Sleeve for Big Bore (750cc) 80mm. Pistons. Note: Stock cylinder sleeves must be removed and the cylinder block Must be bored to accept this larger sleeve and then the new sleeve must be finish bored to accept the new larger big bore pistons...
$285.00
Ex Tax:$259.09